MEP Service in Near South Side Chicago, IL.

Contact Us

Searching for a top rated MEP Firms in Chicago? The one to go to is NY Engineers. Not only for MEP Firms in Chicago but also Construction Engineering and Sprinkler Design Engineering near Near South Side Chicago. Call (+1) 312 767.6877

Contact Us
HVAC Engineering Course

Construction companies throughout Oceanside, New York have come to depend on New York Engineers for a wide range of engineering services ranging from Sprinkler Engineering to CAD to Revit Modeling. For this reason building owners in Near South Side Chicago will tell you that if you’re searching for a top-rated MEP Engineering firm in Near South Side Chicago, IL you need to consider New York Engineers.

Chances are, you might have walked into any specific type of building and observed the outcome of MEP Engineering. Simply put, MEP focuses in the mechanical, electrical and plumbing areas of engineering. In simple terms, the name already gives rise to the most prevalent and correct assumption of what exactly is MEP. This article goes into some infor of what is MEP Engineering.

So far as the mechanical side is involved, for residential and commercial engineering, this handles anything which moves. Moreover its involves the use of complex and easy machines as well as other mechanical mechanisms to carry out certain tasks. Some everyday mechanical engineering tasks which may be noticed everyday are HVAC units, kitchen or bath exhausts, cooling and heating air systems and equipment and systems that take care of increasing the energy productivity.

The electrical facet of construction is centered on the functions, components, electrical safety, and more importantly, the wiring of the building. Engineers with this department try very hard to ensure the layout of any building are meant to deliver adequate electricity to every component in a safe manner where all the electrical codes are met. Some familiar electrical engineering functions are available in the lighting design, regulating the voltage and distributing the energy to each and every component within the structure that demands a supply.

With regards to plumbing, there exists a wide array of plumbing factors that constitute the final design of any structure. Plumbing engineering goes deeper than simply sinks, faucets, and toilets, and contains several behind the scene appliances. These being the drainage line and sewage along with the buildings domestic water supply and just how it flows.

As we conclude this article we now have just reviewed what is MEP Engineering. MEP Engineering is administered inside the construction industry. And, aids in completing the simply ignored technical facets of any building.

Hiring an MEP Engineering Firm in Near South Side Chicago is Important for Major Construction Projects

Hiring an MEP engineering firm in Summit Chicago, ILO, might have everything to do with the safety of your construction project. These engineers can help offset the fee for making this kind of hiring decision when it comes to energy upkeep alone. When you find yourself talking about big commercial structures, energy management is an important topic of discussion. It’s time to learn a few other great reasons for hiring MEP company in Kosciuszko Park Chicago, IL.

Engineers have a lot to do with the structural reliability of any building. If you can well envision, this means the hidden is very vital. Design not simply deals in aesthetics but the base of a building and its components. That may be yet another solid logic why using an MEP engineering company will probably be useful to your project.

Consider each of the pipes and plumbing. Consider the cooling and heating systems and how important it is to get all of its mechanics inside the precise places. Energy conservation was mentioned, and energy competence is an additional important term to discuss. Energy competence is related to your HVAC system, and it plays a vital part in energy conservation overall.

Think of your building’s base. Consider setting up security systems as well as the security and safety measures set up along the entire structure. With everything described so far, it’s reliable advice that many areas of building construction can be either ignored or underestimated short of MEP experts at work.

Now with all you have read you will be looking for the very best MEP engineering firm in the market, right? It’s very clear how the best engineers have to be active in the massive construction of commercial structures. Customized is definitely the proper term to use to illustrate just how these engineers will customize a construction project to meet the needs of the operations. There’s only so much you can save this page if you would like more information on the MEP Engineering services in Near South Side Chicago, Illinois by NY-Engineers.Com you should visit at our blog.

Latest Fire Protection Engineering Related Blog Article

Construction Engineers Explain How HVAC Systems Move Heat

Value Engineering Examples

Heat movement is required for both space heating and air conditioning. Space heating systems deliver heat and air conditioning systems remove it, but the goal in both cases is reaching a suitable indoor temperature. Construction engineers can explain how, though heat can be transmitted across empty space by radiation, using convection and the bulk movement of a fluid is much more effective. In HVAC applications, the most common fluids used to carry heat are air, water, refrigerants, and steam.

Since each substance has different properties, the heat distribution fluid used by an HVAC system determines many performance features. Also consider that different fluid may be used in the same system, with intermediate heat exchange steps.

Heat Distribution with Air

The main advantage of using air to carry heat is simplicity: air is already present in the atmosphere and indoor spaces, so there is no need to use additional fluids in the HVAC system.  Air can interact directly with AC compressors, furnaces or heat pumps to adjust its temperature, and it can then be distributed using fans and ductwork.

However, air ducts require more space than the piping used by other heat-carrying fluids, and they are impractical when air must travel long vertical distances. Consider that warm air rises while cool air tends to fall below, and fan power increases dramatically if you need to move air against its natural behavior. This is neither practical nor energy efficient!

When air ducts must serve separate zones, its distribution is typically controlled with air dampers. These can adjust their position between fully open and fully closed as needed to regulate airflow, and they are controlled automatically by the thermostats in each zone.

One of the most promising system upgrades for air distribution systems promoted by construction engineers is adding variable frequency drives (VFD) to the fans. Reducing fan speed is much more efficient than intermittent operation when you don’t need the full rated airflow. In the case of fractional horsepower fans, a brushless DC motor is recommended instead of a VFD, since they come with built-in speed control.

Packaged rooftop units are an example of an HVAC system that uses air as the main heat distribution and heat removal medium.

Heat Distribution with Water

Some HVAC systems heat or cool water instead of air, and water then interacts with indoor air through fan coils. When this configuration is used, the installation is referred to as a hydronic system. Compared with air, water can hold much more heat per unit of volume, thanks to its higher specific heat and density. As a result, it is the preferred heat-carrying medium in large commercial and industrial installations: hydronic piping uses much less space than air ducts for a given heating or cooling load.

Just like airflow can be controlled with dampers and VFD-equipped fans, the flow of water in a hydronic system can be controlled with valves and VFD-equipped pumps. The basic principle is the same: finding an operating point where each zone is kept at the required temperature and humidity, at the lowest energy cost possible.

Chillers and boilers are two examples of HVAC systems that rely on water to carry heat. Indoor air can then be heated or cooled using fan-coils. Another possible configuration is using larger air-handling units (AHU) connected to an air duct system, where heat exchange occurs between the hydronic piping and the air being circulated by the AHU.

Refrigerant

All air conditioning compressors and heat pumps use refrigerant internally, but there also HVAC systems with longer refrigerant lines connecting different pieces of equipment. Refrigerant lines are even more compact than hydronic piping, not to mention air ducts. Just like when water is used to carry heat, refrigerant flow can be controlled with the combination of valves and variable speed control for the compressor.

Ductless air conditioners and heat pumps use refrigerant lines between the condenser and evaporator units, and typically offer a very high efficiency. The concept can also be applied for multiple zones served by a single outdoor unit, using a variable refrigerant flow system (VRF). VRF systems are very efficient as well, while consolidating heating and cooling systems into a single installation.

Steam

Many buildings in New York City use steam as a heat-carrying fluid, since a significant portion of the city gets steam as a utility service from Con Edison. However, if you plan to install your own boiler, a hot water system is preferred over a steam system.

The main drawback of steam is that you can use it only for heating in most cases. The only way to achieve cooling with steam through an absorption chiller, but a conventional electric chiller is much more economic in multifamily and commercial settings. Absorption chillers are better suited for applications where heat is available at a very low cost or as a waste product of industrial activity – not when you are paying for steam as utility service.

Since steam cannot be used directly for cooling, buildings with steam radiators often have window-type or through-the-wall air conditioning units. These normally suffer from poor efficiency, so you can consider upgrading to ductless units while the heating system is retrofitted to use hot water.

Our Construction Engineers’ Conclusion

HVAC systems are characterized by their variety, and each configuration brings a different set of performance features. Working with qualified HVAC consultants and construction engineers is recommended to identify the system configuration that works best, according to the specific needs of your building. Also keep in mind that only a registered design professional can submit HVAC designs for approval by the NYC Department of Buildings.

Top searches related to Building Commissioning in Near South Side Chicago, IL.

Top Engineering Firms

(MEP) Engineering Service in Near South Side Chicago

MEP Firm Near South Side Chicago! When you're looking for a reliable MEP Firms in Chicago? Your best bet is to contact is New York Engineers. Not only for MEP Chicago but also Architectural Engineering and Sprinkler Design Engineering near Near South Side Chicago. Call us at 312 767.6877 A large group of building owners throughout Holtsville, NY have come to depend on New York Engineers for a wide range of [...]

2018-09-02T16:30:55+00:00