MEP Service in Norwood Park West Chicago, IL.

Contact Us

Searching for the best MEP Firms in Chicago? The one to go to is NY-Engineers.Com. Not only for MEP Chicago but also Architectural Engineering and Protection Engineering throughout Norwood Park West Chicago. Call (+1) 312 767-6877

Contact Us
HVAC Engineering Jobs

Property owners throughout Lindenhurst, New York have come to depend on NY Engineers for a wide range of engineering services ranging from Sprinkler Engineering to Energy Modeling. This is why building owners in Norwood Park West Chicago will tell you that if you are seeking a top-rated MEP Engineering firm in Norwood Park West Chicago, Illinois you need to consider New York Engineers.

It is very possible, you have walked into any specific type of building and witnessed the outcomes of MEP Engineering. To put it simply, MEP focuses around the mechanical, electrical and plumbing facets of engineering. Basically, MEP already gives rise to the most common and correct assumption of precisely what is MEP. This article will go into some details of what is MEP Engineering.

As far as the mechanical aspect is concerned, for residential and commercial engineering, this deals with anything that moves. Moreover its entails using complex and straightforward machines together with other mechanical mechanisms to perform certain tasks. Some ordinary mechanical engineering jobs that may be noticed daily are HVAC units, kitchen or bath exhausts, cooling and heating air systems and equipment and systems which handle enhancing the energy productivity.

The electrical facet of construction is focused on the electrical safety, functions, components, and most importantly, the wiring of any building. Engineers in this department go to great lengths to make sure that the layout of the building are meant to deliver adequate power to each individual component in a safe manner where all of the electrical codes are followed. Some common electrical engineering functions may be found in the lighting design, regulating the voltage and allocating the energy to each and every component inside the structure that needs a supply.

plumbing, there may be a variety of plumbing components that constitute the final design of any structure. Plumbing engineering goes deeper than simply sinks, faucets, and toilets, and holds many behind the scene appliances. These being the drainage line and sewage as well as the buildings household water supply and the way it flows.

As we conclude this article we have just reviewed what is MEP Engineering. MEP Engineering is managed throughout the construction industry. And, supports completing the often unnoticed technical areas of any building.

Hiring an MEP Engineering Firm in Norwood Park West Chicago is Necessary for Large Construction Projects

Employing an MEP company in Kelvyn Park Chicago, ILO, can have a whole lot to do with the prosperity of your construction project. These experts can help offset the expense of making this sort of hiring decision in relation to energy management alone. If you are speaking about huge commercial structures, energy management is a crucial topic of discussion. It’s time to learn some other great factors behind hiring MEP engineering company in Belmont Central Chicago, Illinois.

Engineers have a lot to do with the structural reliability of the building. If you can well imagine, it means the unseen is very vital. Design not merely deals in looks but the base of a building also its workings. Which is the next solid good reason that using an MEP engineering company will likely be good for any project.

Consider every one of the pipes and plumbing. Take into account the cooling and heating systems and the importance of getting all of its mechanics inside the correct places. Energy conservation was discussed, but energy competence can be another important term to speak of. Energy efficiency has everything to do with your HVAC system, and it plays a vital part in energy maintenance in general.

Take into consideration your building’s footing. Consider setting up fire alarm systems as well as the security and safety measures put in place through the entire structure. With everything described thus far, it’s safe to say that numerous areas of building construction may be either ignored or underestimated without MEP experts on the job.

Now with all you have read you are going to be looking for the best MEP engineering company in the industry, right? It is very clear that the best engineers need to be involved in the large construction of commercial structures. Personalized is definitely the right term to use to explain how these engineers will adapt a construction project to meet the requirements of your own operations. Even with all of this information you would like additional information on the MEP Engineering services in Norwood Park West Chicago, IL by NY-Engineers.Com you should visit at our Norwood Park West Chicago Engineering Reports blog.

New Electrical Engineering Related Blog Post

Construction Engineers Present Tips from the Passive House Institute US

Fire Protection Engineer Certification

The Passive House Institute US (PHIUS) is an organization that promotes passive building standards and best practices for construction engineers and others. They also offer certification programs for buildings and products, as well as professional certifications for architects and engineers. This article will provide an overview of some their main guidelines for passive house construction. It is important to note that, although the word “house” is used, these concepts apply for high-rise multifamily buildings and commercial facilities as well.

The PHIUS summarizes its building philosophy as “maximize your gains, minimize your losses”, focusing on achieving synergy between energy efficiency and comfort. The five main principles to consider for passive building are the following:

  1. High-performance insulation
  2. Airtight building envelope
  3. High-performance windows
  4. Using heat and moisture recovery to minimize HVAC expenses
  5. Managing solar heat gain, promoting it during the winter and reducing it during the summer

According to PHIUS, a passive building is around 5% to 10% more expensive than a conventional one, but this is compensated many times during the building lifetime through energy savings. In addition, passive buildings are more comfortable, since they eliminate two main issues affecting conventional buildings: air drafts and temperature fluctuation. In commercial settings, comfort can also lead to increase profits, by stimulating employees to be more productive.

1)   High-Performance Insulation

The main benefit of high-performance insulation is that space heating and cooling loads are reduced. As a result, HVAC systems can be sized smaller, compared with a building that uses the minimum insulation required by construction codes. A smaller HVAC system can be installed with less capital and also has a lower operating cost.

The PHIUS emphasizes the importance of avoiding thermal bridges, which are concentrated spots in the building envelope where insulation is deficient compared with the surroundings. Heat transfer tends to concentrate in thermal bridges, causing unwanted heat gain in the summer and heat loss in the winter.

Current building codes are limited when addressing thermal bridges, since their specifications are based on U-values for insulation and one-dimensional modeling of thermal envelopes. Thermal bridges are a complex three-dimensional phenomenon that can be addressed more effectively with the building modeling software utilized by knowledgeable construction engineers.

2) Airtightness

Air leaks can be just as detrimental as poor insulation when it comes to building envelope performance. Any air exchange between conditioned and unconditioned spaces causes heating and cooling equipment to work harder. Air leakage tends to be more common around windows, doors, plumbing fixtures and electrical fixtures.

In existing constructions, air leakage can be addressed effectively with caulking and weatherstripping. Both have the same purpose, which is blocking spaces where air leakage occurs. The main difference is that caulking is designed for fixed elements like plumbing and electrical fixtures, while weatherstripping is designed to tolerate friction in moving elements like doors and windows. However, caulking should be used for the external edges of door and window frames, which are not subject to relative motion. In new constructions, airtightness can be built into the envelope during the project construction phase.

3) High-Performance Windows

Significant heat transfer occurs through windows, even when the surrounding walls are well insulated. High-performance windows are one of those energy efficiency upgrades that can be deployed in existing constructions, but which is much more cost-effective in new buildings.

  • In an existing building, the upgrade cost is the full price of the window plus the associated labor cost.
  • In new constructions, there is a baseline window and labor cost that is unavoidable, and only the price premium of a high-performance window is considered for financial analysis.

The most energy-efficient windows in the market currently use a triple pane, inert gas to fill the two resulting spaces, a fiberglass frame and low-emissivity coating for the glass. Double pane windows apply the same concept, giving up on part of the energy efficiency to achieve a lower price. However, both triple-pane and double-pane windows are much more efficient than conventional models with single uncoated sheets of glass and metallic frames. A double-pane window is around 50% more efficient than a conventional one, while a triple-pane window provides an efficiency boost of 20-30% compared with a double-pane one.

4) Heat and Moisture Recovery

Since HVAC systems have the goal of controlling temperature and humidity, a higher efficiency can be achieved if the exhaust air is used to precondition the intake air. Heat-recovery ventilation (HRV) only exchanges heat between the supply and exhaust airstreams, while energy-recovery ventilation (ERV) exchanges heat and moisture. The operating principle is reversed for summer and winter conditions:

  • Outdoor air tends to be warmer and more humid during the summer. Therefore, the exhaust air can be used to remove some of its heat and moisture. This reduces the HVAC load and improves energy efficiency.
  • Outdoor air is cool and dry during the winter, so the exhaust air can be used to preheat and humidify it before reaching the HVAC system. This also achieves a load reduction.

5) Solar Heat Gain Optimization

Managing solar heat gain can be tricky. It is beneficial during the winter since it reduces the load on space heating systems; however, during the summer it increases cooling load and must, therefore, be minimized. Also, solar glare should be avoided regardless of the time of the year – it causes discomfort and distraction while having the potential to damage human vision.

Window shades are a simple and effective measure to control solar heat gain. The sun is higher in the sky during the summer, and shades block a larger portion of its radiation. The sun’s altitude drops as winter approaches, and more radiation enters the building, reducing space heating loads. In some locations in the northern hemisphere, is important to note that south-facing windows get the most sunshine throughout the year, and north-facing windows get the least. East-facing windows receive plenty of sunshine during the morning and west-facing windows during the afternoon. Windows should be arranged so that the sun itself is not in direct line-of-sight for occupants. Greater control is possible with optimal building orientation, window shades, and well-placed vegetation.

Construction Engineers Make These Final Recommendations

Developers interested in a passive building can achieve the best results by working with certified design professionals. For example, the Passive House Institute US has the Certified Passive House Consultant (CPHC) program. There are more than 1,300 CPHCs in the USA, and they have been extensively trained in energy modeling software and passive building while considering the variety of climate zones in the USA. The US Green Building Council also offers the LEED certification for construction engineers and other professionals, where many topics covered deal with energy-efficient construction.

searches related to Engineering Reports Norwood Park West Chicago, Illinois.

MEP Consulting Engineers

(MEP) Engineering Service in Norwood Park West Chicago

MEP Norwood Park West Chicago! If you re looking for a fast responding MEP Firms in Chicago? The one to go to is is NY Engineers. Not only for MEP Chicago but also Mechanical Engineering and Sprinkler Engineering near Norwood Park West Chicago. Contact us at (+1) (312) 767.6877 A great number of developers throughout Franklin Square, NY have come to depend on NY-Engineers.Com for a wide range of engineering services [...]

2018-09-15T21:16:31+00:00