MEP Service in South Commons Chicago, IL.

Contact Us

Looking for a top MEP Chicago? Your best bet is to reach out to is NY Engineers. Not only for MEP Engineering in Chicago but also Construction Engineering and Protection Engineering throughout South Commons Chicago. Contact us at (312) 767-6877

Contact Us
Electrical Engineering Degree

Construction companies throughout Peekskill, New York have come to depend on NY Engineers for a wide range of engineering services ranging from Mechanical Engineering to Construction Administration. This is why developers in South Commons Chicago will tell you that if you are seeking a top-rated MEP Engineering firm in South Commons Chicago, Illinois you should consider NY-Engineers.Com.

No doubt, you might have walked through any particular form of building and witnessed the outcomes of MEP Engineering. In other words, MEP centers around the mechanical, electrical and plumbing areas of engineering. In simple terms, the name already gives rise to the most common and accurate notion of exactly what is MEP. Our article should go into some specifics of what is MEP Engineering.

As far as the mechanical aspect is involved, for residential and commercial engineering, this handles anything which moves. Moreover its entails using complex and uncomplicated machines along with other mechanical mechanisms to carry out certain tasks. Some ordinary mechanical engineering tasks which can be noticed daily are HVAC units, kitchen or bath exhausts, cooling and heating air systems and equipment and systems that deal with enhancing the energy efficiency.

The electrical element of construction is centered on the functions, components, electrical safety, and most importantly, the wiring associated with a building. Engineers with this section try very hard to make certain that the layout of any building are made to supply adequate power to every individual component in a safe manner ensuring that all of the electrical codes are followed. Some common electrical engineering jobs can be obtained from the lighting design, modifying the voltage and allocating the energy to every component in the structure that takes a supply.

As far as plumbing, there is certainly a variety of plumbing components which constitute the final design of any building. Plumbing engineering goes deeper than only faucets, toilets, and sinks, and contains many behind the scene appliances. These being the drainage line and sewage and also the buildings local water supply and how it flows.

As we wrap up our article we now have just looked at what is MEP Engineering. MEP Engineering is managed inside the construction industry. And, helps with completing the easily ignored technical facets of any building.

Hiring an MEP Engineering Firm in South Commons Chicago is Important for Major Construction Projects

Using an MEP firm in South Loop Chicago, ILO, can have a whole lot to do with the safety of your construction project. These professionals may help offset the cost of making such a hiring decision in relation to energy conservation alone. When you are speaking about big commercial structures, energy saving is really a topic of discussion. It’s time to determine some other great reasons behind using MEP engineering firm in Nortown Chicago, Illinois.

Engineers have a great deal to do with the structural integrity of the building. As you may well envision, this means the unseen is very vital. Design not simply deals in aesthetics but the underpinning of a building and its components. That is merely another solid good reason that hiring an MEP engineering firm will likely be helpful to any project.

Consider all the pipes and plumbing. Take into account the heating and air conditioning systems and the importance of getting each one of its components inside the exact places. Energy saving was discussed, and energy competence is another important term to mention. Energy competence has everything to do with your HVAC system, plus it plays a huge part in energy conservation as a whole.

Consider your building’s base. Consider installing home security systems along with the safety and security measures put in place through the entire structure. With everything else mentioned to date, it’s reliable advice that numerous facets of building construction can be either ignored or underestimated without MEP professionals at the job.

Now with all you know you are going to look to find the best MEP engineering firm in the business, right? It is very obvious the best engineers have to be in the large scale construction of commercial buildings. Personalized is definitely the correct term to work with to clarify just how these pros will customize a construction project to meet the requirements of your respective operations. There’s only so much you can save this page if you would like more details on the MEP Engineering services in South Commons Chicago, IL by NY-Engineers.Com you should take a look at our blog.

CAD to Revit Modeling Related Blog Article

Construction Engineers Explain How HVAC Systems Move Heat

MEP Consulting Engineers Reviews

Heat movement is required for both space heating and air conditioning. Space heating systems deliver heat and air conditioning systems remove it, but the goal in both cases is reaching a suitable indoor temperature. Construction engineers can explain how, though heat can be transmitted across empty space by radiation, using convection and the bulk movement of a fluid is much more effective. In HVAC applications, the most common fluids used to carry heat are air, water, refrigerants, and steam.

Since each substance has different properties, the heat distribution fluid used by an HVAC system determines many performance features. Also consider that different fluid may be used in the same system, with intermediate heat exchange steps.

Heat Distribution with Air

The main advantage of using air to carry heat is simplicity: air is already present in the atmosphere and indoor spaces, so there is no need to use additional fluids in the HVAC system.  Air can interact directly with AC compressors, furnaces or heat pumps to adjust its temperature, and it can then be distributed using fans and ductwork.

However, air ducts require more space than the piping used by other heat-carrying fluids, and they are impractical when air must travel long vertical distances. Consider that warm air rises while cool air tends to fall below, and fan power increases dramatically if you need to move air against its natural behavior. This is neither practical nor energy efficient!

When air ducts must serve separate zones, its distribution is typically controlled with air dampers. These can adjust their position between fully open and fully closed as needed to regulate airflow, and they are controlled automatically by the thermostats in each zone.

One of the most promising system upgrades for air distribution systems promoted by construction engineers is adding variable frequency drives (VFD) to the fans. Reducing fan speed is much more efficient than intermittent operation when you don’t need the full rated airflow. In the case of fractional horsepower fans, a brushless DC motor is recommended instead of a VFD, since they come with built-in speed control.

Packaged rooftop units are an example of an HVAC system that uses air as the main heat distribution and heat removal medium.

Heat Distribution with Water

Some HVAC systems heat or cool water instead of air, and water then interacts with indoor air through fan coils. When this configuration is used, the installation is referred to as a hydronic system. Compared with air, water can hold much more heat per unit of volume, thanks to its higher specific heat and density. As a result, it is the preferred heat-carrying medium in large commercial and industrial installations: hydronic piping uses much less space than air ducts for a given heating or cooling load.

Just like airflow can be controlled with dampers and VFD-equipped fans, the flow of water in a hydronic system can be controlled with valves and VFD-equipped pumps. The basic principle is the same: finding an operating point where each zone is kept at the required temperature and humidity, at the lowest energy cost possible.

Chillers and boilers are two examples of HVAC systems that rely on water to carry heat. Indoor air can then be heated or cooled using fan-coils. Another possible configuration is using larger air-handling units (AHU) connected to an air duct system, where heat exchange occurs between the hydronic piping and the air being circulated by the AHU.

Refrigerant

All air conditioning compressors and heat pumps use refrigerant internally, but there also HVAC systems with longer refrigerant lines connecting different pieces of equipment. Refrigerant lines are even more compact than hydronic piping, not to mention air ducts. Just like when water is used to carry heat, refrigerant flow can be controlled with the combination of valves and variable speed control for the compressor.

Ductless air conditioners and heat pumps use refrigerant lines between the condenser and evaporator units, and typically offer a very high efficiency. The concept can also be applied for multiple zones served by a single outdoor unit, using a variable refrigerant flow system (VRF). VRF systems are very efficient as well, while consolidating heating and cooling systems into a single installation.

Steam

Many buildings in New York City use steam as a heat-carrying fluid, since a significant portion of the city gets steam as a utility service from Con Edison. However, if you plan to install your own boiler, a hot water system is preferred over a steam system.

The main drawback of steam is that you can use it only for heating in most cases. The only way to achieve cooling with steam through an absorption chiller, but a conventional electric chiller is much more economic in multifamily and commercial settings. Absorption chillers are better suited for applications where heat is available at a very low cost or as a waste product of industrial activity – not when you are paying for steam as utility service.

Since steam cannot be used directly for cooling, buildings with steam radiators often have window-type or through-the-wall air conditioning units. These normally suffer from poor efficiency, so you can consider upgrading to ductless units while the heating system is retrofitted to use hot water.

Our Construction Engineers’ Conclusion

HVAC systems are characterized by their variety, and each configuration brings a different set of performance features. Working with qualified HVAC consultants and construction engineers is recommended to identify the system configuration that works best, according to the specific needs of your building. Also keep in mind that only a registered design professional can submit HVAC designs for approval by the NYC Department of Buildings.

Common searches related to Sprinkler Engineering South Commons Chicago, IL.

MEP Meaning

(MEP) Engineering Service in South Commons Chicago

MEP South Commons Chicago! When you re looking for a dependable MEP Firms in Chicago? Your best bet is to call is NY Engineers. Not only for MEP Chicago but also Construction Engineering and Sprinkler System Engineering near South Commons Chicago. Contact us at (+1) (312) 767-6877 The great majority of construction companies throughout Newburgh, NY have come to depend on NY Engineers for a wide range of engineering services ranging [...]

2018-09-23T01:03:24+00:00