MEP Service in Vittum Park Chicago, IL.

Contact Us

Looking for a top rated MEP Chicago? The one to go to is NY-Engineers.Com. Not only for MEP Firms in Chicago but also Mechanical Engineering and Sprinkler Engineering near Vittum Park Chicago. Call 312 767-6877

Contact Us
Electrical Engineering Subjects

Property owners throughout Glen Cove, NY have come to depend on New York Engineers for a wide range of engineering services ranging from Electrical Engineering to Value Engineering. For this reason real estate investors in Vittum Park Chicago will tell you that if you are seeking a top-rated MEP Engineering firm in Vittum Park Chicago, IL you should consider New York Engineers.

It is very possible, you have walked into any specific sort of building and witnessed the outcome of MEP Engineering. Simply put, MEP focuses in the mechanical, electrical and plumbing aspects of engineering. In essence, MEP already gives a clue to the most prevalent and precise assumption of what exactly is MEP. Our article should go into some details of what is MEP Engineering.

As far as the mechanical side is concerned, for residential and commercial engineering, this works with anything that moves. In addition its involves using complex and simple machines along with other mechanical mechanisms to do certain tasks. Some normal mechanical engineering tasks which is often noticed everyday are HVAC units, kitchen or bath exhausts, cooling and heating air systems and equipment and systems that cope with increasing the energy productivity.

The electrical facet of construction is centered on the functions, components, electrical safety, and above all, the wiring of any building. Engineers with this section go to great lengths to make certain that the schematics of the building are meant to bring sufficient electricity to every component in a safe manner ensuring that all of the electrical codes are followed. Some familiar electrical engineering tasks can be found in the lighting design, modifying the voltage and allocating the power to every single component inside the structure that demands a supply.

With regards to plumbing, there may be a wide array of plumbing components which make up the final model of any building. Plumbing engineering goes deeper than simply faucets, toilets, and sinks, and accommodates several behind the scene devices. These being the drainage line and sewage as well as the buildings domestic water supply and exactly how it flows.

As we conclude this article we now have just considered what is MEP Engineering. MEP Engineering is managed in the construction industry. And, helps with completing the simply unnoticed technical elements of any building.

Hiring an MEP Engineering Firm in Vittum Park Chicago is Important for Huge Construction Projects

Using an MEP engineering company in Noble Square Chicago, Illinois, may have everything to do with the prosperity of your construction project. These specialists can help offset the fee for making this sort of hiring decision when it comes to energy management alone. When you find yourself discussing big commercial structures, energy conservation is a vital topic of discussion. It’s time to find out various other great reasons behind employing MEP company in Chatham Chicago, Illinois.

Engineers have everything to do with the structural reliability of any building. As you may well imagine, this means the unseen is extreamly vital. Design not simply deals in aesthetics but the groundwork of a building and its mechanism. Which is merely another solid logic why hiring an MEP engineering company will likely be useful to any project.

Take into consideration every one of the pipes and plumbing. Take into account the air conditioning systems and how important it is to get all its components inside the precise places. Energy maintenance was stated, however energy competence is an additional vital term to bring up. Energy efficiency is related to your HVAC system, plus it plays a huge role in energy conservation overall.

Take into consideration your building’s foundation. Consider the installation of fire alarm systems and also the safety and security measures set up along the entire structure. With everything else described to date, it’s reliable advice that numerous areas of building construction may be either ignored or underestimated short of MEP experts at work.

Now with all you know you are going to look to find the best MEP engineering firm available, right? It is very obvious how the best engineers need to be in the large construction of commercial structures. Customized is the correct term to utilize to clarify how these specilists will alter a construction job to meet the requirements of your respective operations. Even with all of this information you would like additional info about the MEP Engineering services in Vittum Park Chicago, Illinois by New York Engineers you should visit at our blog.

Latest MEP Engineering Related Post

MEP Engineering Tips: 7 Ways to Minimize Mechanical Space

Value Engineering Examples In Construction

In any MEP engineering project, the Mechanical equipment carries out a fundamental role in residential, commercial, and industrial locations, performing functions such as:

  • Space cooling and heating
  • Supplying chilled or hot water
  • Refrigeration
  • Ventilation
  • Indoor humidity control

These types of equipment and their associated ductwork and piping are notorious for their high space requirements, but there are several ways to make mechanical installations more compact.

1)      Installing Boilers as Close to the Roof as Possible

Boilers that operate with the combustion of fuels such as oil, propane, natural gas, biomass, or biodiesel require a chimney to exhaust their flue gases. Since the chimney must cross the entire distance from the boiler to the rooftop, its space requirements are increased as the boiler is located farther from the uppermost level – there are more floors to go through.

Installing a boiler at the highest possible location in a building shortens the chimney, which offers three significant advantages:

  • The space that the chimney would have used on each floor is freed up for other purposes.
  • The installation becomes safer, because the risk of flue gases being released indoors is minimized.
  • The cost of the chimney is reduced.

An alternative to installing boilers on the attic or the uppermost floor of a building is to simply use a heating technology that does not require a chimney, such as an electric resistance heater or a heat pump. A solar water heater is also a viable option: it is located on the rooftop, saving indoor space, and it runs with sunlight, a free energy input.

2)      Installing Air Conditioning Units on Ceilings

The largest individual component of an air conditioning system is typically the condenser, which is normally located outdoors. When installed on the external walls of a home or building, condensers occupy plenty of space and may even represent an obstacle for outdoor circulation if located on the first floor.

Condensers also release a lot of heat, and the circulation of warm air may be restricted when outdoor spaces are reduced due to proximity with another building or a wall. This has two negative consequences that MEP engineering professionals must consider: warm air can make outdoor locations uncomfortable, and it reduces the operating efficiency of condensers. On the other hand, if a condenser is located on a rooftop, warm air can circulate more freely, and noise becomes less of an issue.

In large commercial or industrial facilities, the equipment used by air conditioning and cooling systems is much larger, but the same logic applies – installing these units on rooftops saves considerable outdoor space. However, this is only feasible if the structure is strong enough to support the weight. Examples of equipment that may be found outdoors in a typical commercial or industrial MEP engineering project settings include:

  • Packaged rooftop air conditioning units
  • Air-cooled chillers
  • Cooling towers for industrial processes or for water-cooled chiller plants

3)      Using the Same System for Cooling and Heating

A heat pump operates with the refrigeration cycle, the same physical principle on which air conditioners are based, with the difference that it operates in reverse – it extracts heat from the cooler outdoor environment and uses it for space or water heating. In addition, some heat pumps are reversible, which allows them to consolidate heating and cooling into a single piece of equipment.

Upgrading to a heat pump can also result in energy efficiency improvements. There are two key pieces of information to look for when comparing heat pump models:

  • The Seasonal Energy Efficiency Ratio (SEER) is the ratio of cooling output to energy input during the cooling season.
  • The Heating Seasonal Performance Factor (HSPF) is basically the same concept, but for when the heat pump is operating in heating mode.

The SEER and HSPF are ratios that relate BTUs (British Thermal Units) and watt-hours, and a higher value translates into reduced energy consumption: it means the unit needs less energy to meet a specific cooling or heating load. For example, an air conditioner with a SEER of 20 will only draw half the power of a SEER 10 unit, assuming both have the same cooling output.

Alternatively, unit efficiency may be reported as a Coefficient of Performance, which is also a ratio of cooling or heating output and power input, but using watts for all quantities. Heat pumps typically have a COP of 2.5 or more, which means they yield significant savings when replacing resistance heaters, whose COP is 1.

In MEP engineering, an ideal scenario for upgrading to a heat pump would be if a household uses a resistance heater and an old air conditioning unit. In this case, a heat pump would consolidate two devices into one, while improving energy efficiency in both modes of operation.

For industrial applications, using an absorption chiller is a viable option for consolidating heating and cooling systems. This type of chiller can use waste heat from a steam plant or an industrial process, and provide cold water for space and process cooling. It is important to note, however, that absorption chillers are viable only when there is sufficient waste heat; otherwise, a normal compression-based chiller is a better choice.

4)      Installing Mechanical Equipment in Normally Unused Spaces

Another viable strategy to minimize the useful indoor space on your next MEP engineering project that is typically taken up by mechanical equipment is to install these units in a location that is not normally used. One example of such locations is:

  • Roof Bulkheads – This is one type of structure that is found on many buildings and is rarely used. Their main purpose is providing access to the roof, and they tend to be used more during construction and maintenance than during actual building operation.

5)      Using Mini-Split Systems Instead of Packaged Rooftop Units for Small Buildings

Packaged rooftop units allow multiple condensers to be consolidated as a single unit, but they require considerable space for ductwork. In small residential and commercial locations, mini-split systems are often the superior choice, offering a simpler installation and superior energy efficiency. Packaged rooftop units normally go up to SEER 15, while mini-split systems are available with efficiency ratings of SEER 25 or above.

Mini-split systems are a practical choice in commercial locations that are split into several zones with independent schedules, such as open-air shopping malls. As locations become larger, rooftop packaged units emerge as the preferred choice – too many compressors and evaporators would be required to offer air conditioning with mini-split units.

6)      Vertically Aligning Equipment on Several Floors

Multi-story buildings normally have components that are repeated floor by floor, and mechanical equipment is no exception to this. For example, air conditioning systems in tall buildings often use a central chiller plant to cool water, which is then supplied to air handling units (AHU) that cool the air in each floor.

If AHUs and similar units are aligned vertically floor by floor, it is possible to distribute cold water to all of them with a single pipe running vertically across the building. Since ductwork is installed above the false ceiling, most mechanical equipment will be located out of sight.

The associated electrical installations providing power to mechanical equipment also become more compact when similar units are aligned vertically or horizontally. Multiple circuits can be installed within a single conduit run, and it is also possible to use a bus duct for equipment drawing high current.

7)      Hiring Qualified MEP Engineering Professionals for the Design Stage

A well-organized mechanical installation takes up less space, and making sure the layout is as simple as possible is a process that starts from the project design phase. If mechanical, electrical, and plumbing installations (MEP) are designed together, equipment and associated components can be specified and located with the following goals in mind:

  • Minimizing the space and materials requirements.
  • Avoiding clutter caused by components from different buildings systems.

There are now software packages that allow 3D MEP models to be created and visualized before starting the construction process — including Revit. These models are of great assistance when planning how mechanical installations will be laid out on your next MEP engineering project, and are also very useful for contractors during materials takeoff and construction.

Conclusion

Optimizing the space used by mechanical equipment in your MEP engineering projects offers several advantages beyond comfort. It may be possible to reduce the cost of installations, and in many cases it also increases energy efficiency. The best way to ensure a mechanical installation offers top performance and an optimal layout is to hire qualified designers and contractors for the project.

Common searches related to MEP Engineering in Vittum Park Chicago, IL.

Structural Engineering Near Me

(MEP) Engineering Service in Vittum Park Chicago

MEP Company Vittum Park Chicago! If you're searching for a reliable MEP Firms in Chicago? The top choice is is NY-Engineers.Com. Not only for MEP Firms in Chicago but also Value Engineering and Protection Engineering throughout Vittum Park Chicago. Call 312 767.6877 A great number of building owners throughout Melville, NY have come to depend on NY-Engineers.Com for a wide range of engineering services ranging from Electrical Engineering to CAD to [...]

2018-09-21T21:56:35+00:00