Electrical Engineer Service Kirkland Washington2019-03-08T02:01:21+00:00

Electrical Engineer Services in  Kirkland Washington

Value Engineering Examples In Construction

From Massachusetts to South Dakota general contractors have come to rely on us when they need reliable MEP Engineering Services in or near Kirkland Washington. With that said, it is adequate to note that MEP.NY-Engineers.Com is more than that. We are eight national engineering outfit offering design but also advisory services. Even though we are focused on mechanical, electrical and plumbing (MEP) installations. MEP.NY-Engineers.Com offers a range of services to property developers and business owners. These services range from compliance with national standards, as well as building codes specific to each state or city. this ensures a quick project approval with local authorities to energy efficiency, specifying building systems that accomplish their intended function while saving electricity and fuel and more. Lately we have seen an increased demand for Electrical Engineering Services in Kirkland Washington. This is an area where we is good at.

Why you ought to consider New York Engineers for all your electrical engineer projects? If you are in the course of arranging a major project, and that project calls for electrical work, you should consider hiring an electrical engineer. You can even want to investigate using a professional when you have electrical things that you are looking to solve. Why would you be hiring a professional? Following are some of the perks you’ll be able to enjoy if you work with an Electrical Engineer.

They’ll Enable You To Avoid Huge Blunders – It’s not unusual for anyone to make mistakes in terms of electrical work. Sadly, most of these blunders could have overwhelming effects. You’ll want to work alongside someone who is mindful of anything that may go wrong. In the event you hire someone who has the right expertise, they’ll have the ability to make certain that the project that you’re planning, goes off with no hitch.

They May Provide A Great Deal Of Useful Advice – You will possibly not have much exposure to electrical work. Thankfully, these pros have a lot of knowledge that you just don’t. They’ll be able to give feedback and advice that might be truly helpful to you. If you do find yourself dealing with someone similar to this, you’ll find yourself taking a lot of their comments aboard.

They Can Aid You To Complete A Project On Schedule – Plenty of projects such as this find yourself getting delayed, and these kinds of delays can be quite costly. Should this be something which you’d choose to prevent, an experienced can make sure that you won’t go off your schedule.

There are many reasons to contemplate hiring an electrical engineer. If you’re arranging a major project, and you believe you could use an engineer, you should begin talking to some professionals that are inside your general area. At New York Engineers, we have been able to help hundreds of developers who were searching for Electrical Engineering Services in or near Kirkland Washington with not only that but also services such as Electrical Engineering. If you would like additional info on the services we provide please, consider on our blog.

Latest Post Related to Electrical Engineer Services in Kirkland Washington

Construction Engineers Explain How HVAC Systems Move Heat

Value Engineering Ppt

Heat movement is required for both space heating and air conditioning. Space heating systems deliver heat and air conditioning systems remove it, but the goal in both cases is reaching a suitable indoor temperature. Construction engineers can explain how, though heat can be transmitted across empty space by radiation, using convection and the bulk movement of a fluid is much more effective. In HVAC applications, the most common fluids used to carry heat are air, water, refrigerants, and steam.

Since each substance has different properties, the heat distribution fluid used by an HVAC system determines many performance features. Also consider that different fluid may be used in the same system, with intermediate heat exchange steps.

Heat Distribution with Air

The main advantage of using air to carry heat is simplicity: air is already present in the atmosphere and indoor spaces, so there is no need to use additional fluids in the HVAC system.  Air can interact directly with AC compressors, furnaces or heat pumps to adjust its temperature, and it can then be distributed using fans and ductwork.

However, air ducts require more space than the piping used by other heat-carrying fluids, and they are impractical when air must travel long vertical distances. Consider that warm air rises while cool air tends to fall below, and fan power increases dramatically if you need to move air against its natural behavior. This is neither practical nor energy efficient!

When air ducts must serve separate zones, its distribution is typically controlled with air dampers. These can adjust their position between fully open and fully closed as needed to regulate airflow, and they are controlled automatically by the thermostats in each zone.

One of the most promising system upgrades for air distribution systems promoted by construction engineers is adding variable frequency drives (VFD) to the fans. Reducing fan speed is much more efficient than intermittent operation when you don’t need the full rated airflow. In the case of fractional horsepower fans, a brushless DC motor is recommended instead of a VFD, since they come with built-in speed control.

Packaged rooftop units are an example of an HVAC system that uses air as the main heat distribution and heat removal medium.

Heat Distribution with Water

Some HVAC systems heat or cool water instead of air, and water then interacts with indoor air through fan coils. When this configuration is used, the installation is referred to as a hydronic system. Compared with air, water can hold much more heat per unit of volume, thanks to its higher specific heat and density. As a result, it is the preferred heat-carrying medium in large commercial and industrial installations: hydronic piping uses much less space than air ducts for a given heating or cooling load.

Just like airflow can be controlled with dampers and VFD-equipped fans, the flow of water in a hydronic system can be controlled with valves and VFD-equipped pumps. The basic principle is the same: finding an operating point where each zone is kept at the required temperature and humidity, at the lowest energy cost possible.

Chillers and boilers are two examples of HVAC systems that rely on water to carry heat. Indoor air can then be heated or cooled using fan-coils. Another possible configuration is using larger air-handling units (AHU) connected to an air duct system, where heat exchange occurs between the hydronic piping and the air being circulated by the AHU.

Refrigerant

All air conditioning compressors and heat pumps use refrigerant internally, but there also HVAC systems with longer refrigerant lines connecting different pieces of equipment. Refrigerant lines are even more compact than hydronic piping, not to mention air ducts. Just like when water is used to carry heat, refrigerant flow can be controlled with the combination of valves and variable speed control for the compressor.

Ductless air conditioners and heat pumps use refrigerant lines between the condenser and evaporator units, and typically offer a very high efficiency. The concept can also be applied for multiple zones served by a single outdoor unit, using a variable refrigerant flow system (VRF). VRF systems are very efficient as well, while consolidating heating and cooling systems into a single installation.

Steam

Many buildings in New York City use steam as a heat-carrying fluid, since a significant portion of the city gets steam as a utility service from Con Edison. However, if you plan to install your own boiler, a hot water system is preferred over a steam system.

The main drawback of steam is that you can use it only for heating in most cases. The only way to achieve cooling with steam through an absorption chiller, but a conventional electric chiller is much more economic in multifamily and commercial settings. Absorption chillers are better suited for applications where heat is available at a very low cost or as a waste product of industrial activity – not when you are paying for steam as utility service.

Since steam cannot be used directly for cooling, buildings with steam radiators often have window-type or through-the-wall air conditioning units. These normally suffer from poor efficiency, so you can consider upgrading to ductless units while the heating system is retrofitted to use hot water.

Our Construction Engineers’ Conclusion

HVAC systems are characterized by their variety, and each configuration brings a different set of performance features. Working with qualified HVAC consultants and construction engineers is recommended to identify the system configuration that works best, according to the specific needs of your building. Also keep in mind that only a registered design professional can submit HVAC designs for approval by the NYC Department of Buildings.

Architectural Engineering Degree