Electrical Engineer Service Littleton Colorado2019-03-10T16:49:11+00:00

Electrical Engineer Services in  Littleton Colorado

Construction Engineering Vs Civil Engineering

From Guam to South Carolina developers have come to rely on MEP.NY-Engineers.Com when they need reliable MEP Engineers in Littleton Colorado. With that said, it is adequate to highlight that NY Engineers is more than that! We are eight national engineering outfit offering not only design but also consulting services. Even though our focus is in mechanical, electrical and plumbing (MEP) installations. New York Engineers offers a wide range of services to property developers and business owners. These services range from compliance with national standards, as well as building codes specific to each state or city. this ensures a quick project approval with local authorities to project management and commissioning, ensuring all systems are installed and configured according to the approved design documents and more. As of late we have seen an increased demand for Electrical Engineers in or near Littleton Colorado. That is an area where New York Engineers excels at.

Good reasons to consider NY-Engineers.Com for all your electrical engineer projects? When you’re in the course of arranging a major project, and this project calls for electrical work, you should consider hiring an electrical engineer. You might also want to examine using a professional for those who have electrical problems that you are attempting to solve. Why would you be hiring a professional? Following are a couple of the perks you’ll be capable of enjoy if you work with an expert.

They’ll Help You To Avoid Major Mistakes – It’s not rare for individuals to make mistakes with regards to electrical work. Sadly, these kinds of blunders could have devastating outcomes. You’ll want to use someone that’s aware of exactly what can go wrong. Should you employ someone with all the right expertise, they’ll be able to ensure that the job that you’re planning, goes off without a hitch.

They Can Provide A Lot Of Useful Advice – You might not have much exposure to electrical work. Thankfully, these pros have lots of knowledge which you don’t. They’ll have the ability to provide feedback and advice that can be truly necessary to you. If you do wind up working with someone such as this, you’ll realise you are taking a lot of their comments aboard.

They Can Assist You To Finish A Project On Schedule – Lots of projects like this end up getting delayed, and most of these delays can be very costly. If this sounds like an issue that you’d choose to prevent, an expert will be able to make certain you won’t go off your schedule.

There are numerous reasons to consider hiring an electrical engineer. If you’re planning for a major project, and you think that you could use the services of an engineer, you should start speaking to some professionals which can be with your general area. At NY-Engineers.Com, we have been able to help a lot of construction companies who were searching for Electrical Engineering Services near Littleton Colorado with not only that but also services such as Building Commissioning. If you would like more info on the services offered by New York Engineers we ask that you visit on our blog.

Popular Post Related to Electrical Engineer Services in Littleton Colorado

What MEP Engineers Want you to Know About Types of Electric Heat Pumps and Their Advantages

Fire Protection Engineering Companies

Before designing the space heating and domestic hot water systems of a building, a key step for MEP engineers is to determine the energy source to run these appliances. Natural gas or fuel oil combustion comes with a lower operating cost than electric resistance heating, but these fuels produce emissions and require an exhaust system. On the other hand, electric heaters have the potential to be emissions-free if they run with solar or wind power.

Resistance heaters are the most common configuration that runs with electricity, but their operating cost can be extremely high considering the electric tariffs in some cities. However, electric heat pumps can normally deliver from 2 to 4 units of heat per unit of electricity consumed, offering a much lower running cost than an equivalent resistance heater. For a given amount of energy delivered, electricity is much more expensive than gas in some areas, but electric heat pumps can match the running cost of gas boilers by using the energy input more efficiently.

This article will provide an overview of the two main electric heat pump configurations: air-source and geothermal systems.

Air-Source Heat Pumps

As implied by their name, air-source heat pumps extract energy from the surrounding air to deliver heat. This is exactly like an air conditioner running in reverse: have you noticed how the outdoor unit makes the air around it warm? Well, a heat pump uses this same effect indoors.

Assuming the same heating capacity, an air-source heat pump with an ENERGY STAR label only draws around 40% of the power required by an electric resistance heater. Their efficiency is indicated by the Heating Seasonal Performance Factor (HSPF), which is a ratio of Btu output to watt-hour input, similar to the gas mileage value of a car. MEP engineers look for the highest HSPF value that fits your budget to maximize energy savings.

Just like air-conditioning systems, air-source heat pumps are available as packaged systems or split systems (ductless). If your property already has ductwork, a packaged heat pump may be best choice. On the other hand, if duct installation is impractical, a ductless system is recommended. ENERGY STAR air-source heat pumps have a minimum HSPF of 8.2 in packaged configuration, and 8.5 in ductless configuration.

Reverse-cycle chillers are a subtype of air-source heat pump that delivers heat to a water reservoir, instead of supplying it directly to indoor air. This setup allows the heat pump to be used with radiant floor heating piping or with fan-coils.

Geothermal Heat Pumps

The temperature of outdoor air varies considerably throughout the year, and air-source heat pumps suffer from reduced efficiency during the coldest days of winter. The ground is much more reliable as source of heat; this system configuration extracts heat directly from the ground, from groundwater, or from a nearby body of water such as a pond or lake. Geothermal heat pump systems are often called water-source heat pumps, since most system configurations use water with antifreeze as a heat exchange medium between the heat pump and the ground.

Geothermal heat pumps offer a higher efficiency than air-source heat pumps. High-efficiency models in the market deliver savings of over 70% compared with electric resistance heaters, and the most efficient geothermal heat pumps in the market save over 80%.

Geothermal heat pumps can be further classified into closed-loop and open-loop systems.

  • Closed-loop systems have a closed piping loop that circulates between the heat pump and the ground, but the water inside never mixes with groundwater.
  • Open-loop systems draw groundwater from a well, circulate it through the heat pump, and then discharge it. Given their operating procedure, open-loop systems are subject to any applicable groundwater discharge regulations.

Closed-loop systems can use either vertical or horizontal water loops, depending on the availability of land. Horizontal loops require trenches at least four feet deep and are suitable in properties with ample land area. On the other hand, vertical loops can go hundreds of feet underground, and are typically used when land is limited – high-rise construction is an example. If the property is close to a body of water such as a pond or lake, the underground water loop can be submerged instead, which results in a much cheaper installation.

MEP Engineers Offer Recommendations to Use Heat Pumps Effectively

If you are considering heat pumps for your building, the best option changes depending on project conditions. Geothermal heat pumps are the most efficient but also the most difficult to install, especially if we’re dealing with a vertical closed-loop system in a high-rise building. Also, consider that geothermal heat pumps require a prior assessment of the ground below your property – the project may be infeasible if the presence of rocks hinders excavation.

Consider a reverse-cycle chiller (RCC) if your installation already uses hydronic piping, or a packaged unit if you already have air ducts. Ductless heat pumps can be a great option in apartment buildings where each dwelling has individual heating and cooling systems. In new constructions, consider a geothermal heat pump, since it is much easier to install the underground water loop when there is no building yet.

If you are ever unsure about which systems are best suited to your project, it is always wise to recruit the help of experienced MEP engineers.

Fire Protection Engineering Schools