HVAC Belmont Terrace Chicago2018-12-03T04:46:11+00:00

HVAC Belmont Terrace Chicago | Expert Power Efficient System Designs

Importance Of Value Engineering
Contact Us!

Do not be confused by our NY-Engineers.Com is your best option if you are looking for Full Service Heating and Air Conditioning (HVAC) Engineering Firm in Chicago Illinois. We’re not only an HVAC Chicago but also a leading provider of Mechanical Engineering Engineering services near Belmont Terrace Chicago. Call us at (312) 767.6877

Contact Us!

As of late huge crowds have been browsing our site looking for MEP Engineering in the Chicago area. That is due primarily due to the reputation we have built in this kind of work. However, a lot of general contractors from Kenilworth to Prospect Heights, don’t know that NY-Engineers.Com is also the ideal choice for anyone looking for HVAC Contractor in Chicago, Illinois

The quest for cost effective buildings involves cost effective HVAC system design. This can include systems for domestic water heating, architectural enclosure, HVAC, lighting, and vertical transportation. The loads for the HVAC systems should come primarily from five different places including lighting (cooling), the building envelope (cooling and heating), ventilation (cooling and heating), equipment for program use (cooling) and occupancy (cooling).
The ventilation load might be a function of either the machines needed so as to introduce it in a space and control contaminant concentration or the amount of people that will use the space. In nearly all climates inside the southwestern and eastern parts of america, to lessen outside ventilation will save energy whenever the exterior air is either humid and warm or very cold.
Governing the ventilation rate is going to be determined by occupancy which is called a form of demand control ventilation. This is a common type of energy conservation approach that is utilized for spaces with occasional or crowded occupancy. Having heating and cooling loads dropped as low as possible can be accomplished by using a high performance building envelope, occupancy sensors, and high performance lighting that uses daylight response of lighting controls.

Chicago HVAC Engineers versus HVAC Techs

If you’ve ever discussed the difference between a HVAC Engineers vs HVAC Engineers, then keep reading:

Chicago HVAC engineers are definitely the people that run the installation of air conditioning systems for residential and commercial buildings. They spend plenty of their day in offices doing higher level supervision and planning of installations nonetheless they do also see job sites from time to time.

But, HVAC technicians tend to do more of the hands-on work with repair and maintenance. A HVAC tech may deal with an engineer to complete several of the installation task, specifically on smaller jobs. On the whole HVAC techs do much more travel and could spend time and effort identifying leaks, changing filters, doing recharges or decommissioning old and outdated systems which use old refrigerants.

HVAC engineers might have the opportunity to make more decisions about systems that are employed, and they also will be the people who would offer assistance with by far the most sensible refrigerants and which systems would best suit a much bigger building. In the industry, there is certainly some challenge between ‘the suits’ and ‘the ones which get their hands dirty’, but the two jobs require an effective familiarity with how air cooling really works. Lately many Internet users have been reading the New York Engineers website searching for HVAC Solutions Chicago. However, the goal of our firm is to be the to go to company for those searching for a HVAC Firm in or near Chicago and or any of our other services including Value Engineering Engineering services. We ask that those searching for additional info about our Heating Cooling Air Conditioning Furnace (HVAC) Engineering Firm in Chicago Illinois takes a look at our blog!

Latest Post Related to HVAC Companies in Chicago

Cut Costs: Simplify Your MEP Engineering Design

MEP Consulting Engineers Reviews

There are savings opportunities throughout the entire engineering process, not just the construction stage. With effective communication and adequate team management, it is possible to optimize the design process and reduce costs of your MEP engineering project without compromising quality. High-level design software also helps: it may come at a high price, but the time and cost savings are significant.

When the engineering design process becomes long and expensive, it is typically due to one of the following factors:

  • Poor communication between design teams. This is especially important in the case of mechanical, electrical and plumbing systems – all three have complex physical layouts, and there is a high chance of overlap between components of different systems when team communication is poor.
  • Excessive changes. MEP designs are carried out on existing architectural plans, which means architectural changes can become very disruptive as the MEP design process approaches completion. Completing the final version of the architectural design is highly recommended before MEP design starts; a major architectural change after MEP design has been completed can greatly extend the design process and its cost. Changes to MEP systems are also disruptive, since they have a high degree of interdependence.

This article will provide some recommendations that can help you simplify the engineering design process while reducing its cost. There is a basic rule of thumb for cost optimization: modifications are cheap or even free when requested early in the design process, and prohibitively expensive when requested in the final stages of construction.

1) Involve All Project Stakeholders Before the Design Process Starts

If the needs and requirements of all parties are clearly stated from the beginning, they can be accounted for during project design. For example, some contractors and equipment vendors may have special requirements; if this information is known before MEP engineering design starts, changes are avoided later. These changes normally add man-hours to the design process, and if omitted they may result in expensive modifications during construction.

Make sure your MEP design team reviews all equipment specifications before the design process starts, ensuring any special requirements are accounted for. Keep in mind that some building systems involve all three areas of MEP; for example, chilled water systems involve both electrical installations and hydronic piping.

2) Follow an Integral Approach for Mechanical, Electrical and Plumbing Design

As previously stated, these three systems have very complex layouts, and if design teams don’t work in coordination, you are very likely to have issues with overlapping equipment locations. Also, keep in mind that all three systems distribute fluids or air throughout the building, and the means of distribution must not interfere with each other.

  • Mechanical systems typically involve air ducts, refrigerant lines and hydronic piping. If combustion-based heating is deployed, there will also be a chimney for flue gases, along with fuel piping and tanks.
  • Electrical Systems involve conduit and wiring, and there are also bus ducts in high-power applications. Keep in mind that transformers, motors, generators, panelboards and similar equipment may require a lot of space, and clearances may be required with respect to walls and other pieces of equipment.
  • Plumbing Systems involve pumps, as well as independent piping for potable water, wastewater, etc.

The layout of ducts and piping must be specified so that the least amount of materials is used, but taking care not to overlap components from different building systems.

3) Use Three-Dimensional MEP Engineering Design Software

There are now MEP design solutions where a three-dimensional model of the building is stored in a web server that can be accessed by all design teams, and building systems are laid out and specified directly on the model. This offers several advantages over conventional two-dimensional design:

  • Equipment locations can be visualized more clearly, especially when components from all three systems must be installed in tight spaces.
  • Modern MEP design software is smart enough to detect overlap, and design engineers can be notified immediately if it occurs. For example, if the optimal location for two pieces of equipment is the same, they can decide which of the two devices can be relocated for the least cost.
  • The confusion associated with different versions of the same design is eliminated; versions no longer exist, since the entire design process is carried out on a unified 3D model.
  • Most three-dimensional MEP design software can calculate all bills of materials (BOM) automatically, further reducing the total man-hours required for the project.

MEP design software has a high upfront cost, but the investment is compensated by the sheer number of man-hours saved. Also, there are now software solutions with the option of paying a recurring monthly fee, instead of an expensive one-time license. This purchasing model tends to be more attractive for smaller companies with limited budgets.

Having a well-trained staff is just as important as implementing a powerful software solution. If you will invest in a high-level MEP design package, make sure your engineering team learns how to use it effectively. For example, software solutions often have keyboard shortcuts and commands that considerably speed up the work, and using them is much faster than clicking on functions with the mouse. The difference may not be evident for a single action, but when you consider the total man-hours saved the effect is significant.

4) Use a Project Management Platform

E-mail is not always practical when coordinating multidisciplinary teams: tasks must be assigned textually, and there is always the chance of missing or misspelling one of the e-mail addresses. There are now project management platforms where team members can be added to common dashboards, and notifications are sent automatically whenever a task is assigned, modified or completed.

Project management platforms allow team members to focus on the tasks assigned, while communication is streamlined and automated in the background. For example, marking a milestone as finished and linking a project deliverable is faster than sending an e-mail to the entire team with the file as an attachment.

5) Consider Outsourcing the Entire MEP Design Process

Having an in-house engineering team may make sense in industrial settings, or other business sectors where technical assistance is required on an ongoing basis. However, there are companies for which the cost of a permanent engineering staff can’t be justified, and in makes more sense to hire an external firm specializing in MEP design and consulting. This way, the client can save the capital and time required for workstations, software and team building, dedicating it to core business activities instead.

If you will follow this approach, we strongly recommend you hire a firm that provides integral MEP design; if you hire separate designers for mechanical, electrical and plumbing installations, projection integration will be a daunting task.

Concluding Remarks

When optimizing the engineering design process, remember that poor team communication and frequent changes are the main factors that increase costs. With the combination of solid management practices, information technologies and strategic outsourcing, you can improve results while cutting costs. Effective communication before and during your MEP engineering project also promotes collaboration and mitigates conflict.

Popular Searches Related to HVAC Chicago