HVAC Chrysler Village Chicago2018-12-05T02:01:10+00:00

HVAC Chrysler Village Chicago | Expert Energy Efficient System Designs

Fire Protection Engineering Magazine
Contact Us

Don’t be misled by our New York Engineers is the top choice if you are searching for Full Service Air Conditioning, Heating & Cooling (HVAC) Engineering Firm in Chicago Illinois. We are not only an HVAC Chicago but also a leading provider of Sprinkler System Engineering services in or near Chrysler Village Chicago. Contact us at (+1) (312) 767.6877

Contact Us

Recently Many individuals have been taking a look at the NY-Engineers.Com website in search of HVAC Engineering in or near Chicago. That is due because of the following we have built in this kind of work. With that said, many general contractors from Bellwood to Naperville, Illinois, do not know that New York Engineers is also a top choice for anyone searching for HVAC Contractor near Chicago!

The quest for cost effective buildings involves energy-efficient HVAC system design. This can include systems for domestic water heating, architectural enclosure, HVAC, lighting, and vertical transportation. The loads for the HVAC systems will come primarily from five different places including lighting (cooling), your building envelope (cooling and heating), ventilation (cooling and heating), equipment for program use (cooling) and occupancy (cooling).
The ventilation load is a purpose of either the devices necessary so as to introduce it into a space and control contaminant concentration or the number of individuals that may use the area. In the vast majority of climates within the eastern and southwestern parts of the usa, to minimize outter air-flow can save energy whenever the exterior air is either humid and warm or very cold.
Controlling the ventilation rate will probably be based on occupancy which is referred to as a type of demand control ventilation. This really is a everyday sort of energy conservation policy which is used for rooms with intermittent or dense occupancy. Having heating and cooling loads dropped as low as possible can be carried out by utilizing a higher performance building envelope, occupancy sensors, and performance lighting that exploits daylight response of lighting controls.

Chicago HVAC Engineers versus HVAC Techs

If you have ever discussed the distinction between a HVAC Technician vs HVAC Technicians, then please read on:

Chicago HVAC engineers would be the individuals who run the installation of air conditioning systems for both commercial and residential buildings. They spend plenty of their work in offices doing advanced level organization and arranging of installations nevertheless they do also see job sites every now and then.

On the other hand, HVAC technicians often do a lot of hands-on work with repair and maintenance. A HVAC tech may work together with an engineer to accomplish a number of the installation work, especially on smaller jobs. Generally speaking HVAC techs do considerably more travel and may spend time and effort changing filters, identifying leaks, doing recharges or getting rid of old and outdated systems which use old refrigerants.

HVAC engineers could possibly have the opportunity to make more decisions about systems that are being used, and so they will be the people that would offer advice about by far the most sensible refrigerants and which systems would be perfect for a larger building. In the trade, there exists some challenge between ‘the suits’ and ‘the ones that get their hands dirty’, but the two jobs require a great knowledge of how air cooling does work. In recent times huge crowds have been getting to the New York Engineers website looking for things like HVAC Supply House Chicago. However, the goal of our firm is to be the to go to organization for those searching for a HVAC Chicago and or any of our other services including Construction Engineering Engineering services. Furthermore everybody looking for additional information about our Heating Cooling Air Conditioning Furnace (HVAC) Engineering Firm in Chicago Illinois stops by at our Value Engineers blog!

Recent Blog Related to HVAC Company in or near Chicago

Advantages of Electronically Commutated Motors in Electrical Engineering

Architectural Engineering Colleges

Electronically commutated motors (ECMs) can achieve significant energy savings in electrical engineering applications where fractional horsepower is required. Although NEMA Premium Efficiency motors with variable-frequency drives provide the most efficient solution to drive equipment above 1 hp, induction motors are outclassed by ECMs as the rated horsepower is reduced.

What is an Electronically Commutated Motor?

Although ECMs are designed to run with an AC power supply, it is important to note they are actually direct-current motors with permanent magnets on their rotor. Unlike conventional DC motors, which create a rotating magnetic field with a combination of brush contacts and slip rings, ECMs achieve the same effect with a voltage rectifier and an electronic control circuit. As a result, the friction and sparks associated with brush contacts are eliminated, and this is one of the reasons why ECMs are so efficient. They also have a longer service life than brushed motors, since the wear associated with sparks and friction is eliminated. Compared with other common types of fractional horsepower motors, ECMs are the top choice in terms of efficiency:

  • Shaded-pole motors are very common and more affordable, but their efficiency is very poor, going below 20% in some cases.
  • Permanent-split capacitor (PSC) motors have an average efficiency of 40%, which means they outclass shaded-pole motors. In terms of efficiency, they are an intermediate option between shaded-pole motors and ECMs.
  • ECM efficiency is normally above 60%, which means they consume one-third of the energy used by shaded-pole motors on average.

ECMs can also be manufactured with built-in speed control circuits, allowing them to operate at reduced speed without relying on an external VFD. It is also important to note that ECMs do not suffer a drastic reduction in their efficiency when operating below rated RPM. Fixed-speed ECMs are also available for applications where speed control is not necessary.

Electronically Commutated Motors in Electrical Engineering Applications

ECMs are normally the most efficient option in fractional horsepower applications, but they tend to deliver the highest savings when used in air-conditioning and refrigeration systems. Being more efficient that shaded-pole and PSC motors, they also dissipate less heat, and the reduced heating effect helps AC and refrigeration systems operate more efficiently. This effect applies for all air-conditioning or refrigeration components that are found inside the conditioned space, such as air handlers and evaporators.

As an example, assume a cold-storage room has an evaporator unit with five shaded-pole motors, consuming 900W each. They are replaced with ECMs that only consume 300 W each.

  • 600 W are saved per motor, for a total of 3,000 W.
  • However, these 3,000 W are also subtracted from the refrigeration load. If the system operates with a coefficient of performance of 3, an extra 1,000 W of electric power are saved.
  • In other words, this upgrade saves 3 kW in motor power and 1 kW thanks to refrigeration load reduction.

Keep in mind this is just a simple example, and each electrical engineering project requires a detailed analysis to know the exact savings. However, the heating reduction benefit applies for all cases where ECM motors are deployed in air-conditioned or refrigerated locations.

The brushless design of ECMs makes them quieter than their less efficient counterparts, which also provides a comfort advantage. In business applications, the silent operation of ECMs helps employees concentrate better. ECMs are also lighter than other types of fractional horsepower motors, which makes them easier to install.

Electronically Commutated Motors in Ventilation Systems

As previously stated, shaded-pole and PSC motors are inefficient. Also, three-phase motors with VFDs are impractical for fractional horsepower applications, unable to offer the efficiency that characterizes them in larger systems. Ventilation systems represent an excellent opportunity to deploy ECMs, for two main reasons:

  • Fans with fractional horsepower are common, which means they are often driven by shaded-pole or PSC motors.
  • Many fans have intermittent operation, which represents a chance to use ECMs running at reduced speed. For example, running a fan 80% of the time saves 20% of the energy, while running it at 80% speed saves nearly 50%.

ECMs are a highly recommended upgrade for furnace fans, since they can achieve a much more uniform temperature distribution with their speed control, in addition to offering the energy savings that characterize them.

Payback Period of ECM Upgrades

Like with many energy efficiency measures, the financial benefit of an ECM upgrade changes depending on project conditions. The project payback period can only be calculated with precision after a detailed analysis by a professional energy consultant, but in general the following results can be expected:

  • Replacing shaded-pole motors normally yields a faster payback period than replacing PSC motors, since the efficiency gain is higher. Of course, there can be exceptions; replacing a PSC motor that is used frequently may yield higher savings than upgrading a shaded-pole motor that is only used moderately.
  • ECMs can also be an attractive option in appliances that require speed control. Other types of motors may suffer a drastic efficiency reduction at partial speed.
  • As previously mentioned, the energy savings are higher when ECMs are deployed in air-conditioned or refrigerated spaces.

The financial return of an ECM upgrade can also be enhanced if there are incentive programs at the project’s location. The incentive is calculated based on yearly energy savings, at a rate of $0.16/kWh.

Conclusion

Electronically-commutated motors (ECMs) can achieve significant energy savings in fractional horsepower applications, especially when they replace shaded-pole motors. However, like with any energy efficiency upgrade, professional guidance is highly recommended when defining the project scope and specifications.

When upgrading to ECMs, the return on investment is higher in some cases, and it others the payback period may be too long to justify the upgrade. Ideally, upgrades should focus on where the highest return is obtained from each dollar spent upfront. Recruit the help of an electrical engineering expertise to help you properly apply the information shared in this article to your project.

Top Searches Related to HVAC Contractor near Chicago