HVAC Legends South Chicago2018-11-19T00:16:20+00:00

HVAC Legends South Chicago | Expert Energy Efficient System Designs

Architectural Engineers
Contact Us!

Do not be misled by the name New York Engineers is your best option if you seek a Full Service Heating and Air Conditioning (HVAC) Engineering Firm in Chicago Illinois. We are not only an HVAC Firm in or near Chicago but also a leading provider of Mechanical Engineering Engineering services throughout Legends South Chicago. Contact us at (+1) 312 767-6877

Contact Us!

In recent times huge crowds have been visiting the New York Engineers website searching for HVAC Engineering in or near the Chicago area. This is due because of the reputation we have built in this kind of work. However, a lot of builders from Bellwood to Quincy, Illinois, do not know that New York Engineers is also a top choice for anyone looking for HVAC Companies in or near Chicago, Illinois.

The search for power efficient buildings involves energy-efficient HVAC system design. This will include systems for lighting, architectural enclosure, domestic water heating, HVAC, and vertical transportation. The loads for your HVAC systems should come primarily from five different bases including lighting (cooling), the property envelope (cooling and heating), ventilation (cooling and heating), equipment for program use (cooling) and occupancy (cooling).
The ventilation load will certainly be a purpose of either the machines required to be able to introduce it in a space and control contaminant concentration or the number of persons which will occupy the area. In nearly all climates within the eastern and southwestern parts of america, to lower outside air flow will save energy whenever the surface air is either humid and warm or very cold.
Governing the ventilation rate will be dependant upon occupancy which is known as a kind of demand control ventilation. This can be a common type of energy conservation approach that is used for spaces with occasional or heavy occupancy. Having heating and cooling loads dropped as low as possible can be carried out by making use of a very high performance building envelope, occupancy sensors, and performance lighting that employs daylight response of lighting controls.

Chicago HVAC Engineers versus HVAC Technicians

If you’ve ever discussed the distinction between a HVAC Technician versus HVAC Engineers, then continue reading:

Chicago HVAC engineers would be the individuals who oversee the installation of air-con systems for residential and commercial buildings. They spend lots of their time in offices doing higher-level organization and planning of installations but they do also visit job sites every once in awhile.

But, HVAC technicians in Chicago have a tendency to do a lot of hands-on work with repair and maintenance. A HVAC technician may assist an engineer to accomplish a number of the installation work, particularly for smaller jobs. Generally HVAC techs do considerably more travel and may spend considerable time identifying leaks, changing filters, doing recharges or decommissioning old and outdated systems that utilize old refrigerants.

HVAC engineers might have a chance to make more decisions about systems that are employed, and so they will be the folks that would offer advice about one of the most sensible refrigerants and which systems would best suit a larger building. In the industry, there exists some conflict between ‘the suits’ and ‘the ones which get their hands dirty’, but the two jobs require an excellent expertise in how air conditioner works. Nowadays a lot of Internet users have been browsing the NY Engineers site looking for things like HVAC Convention Chicago 2019. Nevertheless, the goal of our company is to become the number one choice for anyone looking for a HVAC Firm in Chicago and or any of our other services including Electrical Engineering Engineering services. Furthermore those looking for additional information about our Heating and Air Conditioning (HVAC) Engineering Firm in Chicago Illinois stops by at our Utility Filings blog

Top Blog Related to HVAC Chicago

Mechanical Engineering Design Options to Heat and Cool Residential Buildings

Mechanical Engineering Salary

There is a broad range of mechanical engineering and design options available for meeting the heating and cooling needs of residential buildings. Normally, these systems differ in terms of the medium used to deliver their heating or cooling output.

  • Water Piping: Water source heat pumps, radiators using chillers, cooling towers, and boilers.
  • Air Ducts: Packaged rooftop units, packaged ceiling hung units
  • Refrigerant Lines: Split AC systems, VRF systems
  • Direct: Used by window-type air conditioners and PTAC units, which operatedirectly between indoor and outdoor locations, without ducts.

This article will provide an overview of some of the most common mechanical design options used for indoor residential spaces, as well as the strengths and limitations of each type of system:

Detailing Mechanical Engineering and Design Options

Mechanical Design Option #1: Four-Pipe System with Chiller, Cooling Tower, and Boiler

This mechanical design gets its name from the fact that it has two separate water circuits, one carrying hot water and another carrying chilled water, each with a supply and return pipe. The basic operating principle of four-pipe systems is the following:

  • Cooling is accomplished by a chiller and cooling tower: A chilled water circuit is used to remove heat from indoor spaces, and the cooling tower is used to reject it outdoors. If the chiller’s compressor comes equipped with a variable-speed drive, this system can offer a very high efficiency in cooling mode.
  • Heating efficiency is determined by the type of boiler. In general, gas-fired boilerstend to be more cost-effective than those running on oil or electrical resistance heating.
  • Fan-coil units are equipped with both hot and cold water coils, granting them the flexibility of either mode of operation.

The main advantage of four-pipe systems is their ability to use both modes of operation simultaneously and independently. This can be especially useful if heating and cooling needs are different across building zones, and especially in apartment buildings and multi-family dwellings where preferences and schedules normally vary by occupant. Of course, a four-pipe system is an expensive mechanical engineering system to install due to the presence of three separate water circuits: two for the distribution of cold and hot water, and a third one used by the chiller to reject heat through the cooling tower.

Mechanical Design Option #2: Water-Source Heat Pumps with Cooling Tower and Boiler

A heat pump can be described in simple terms as a reversible air conditioner: it can deliver indoor cooling through the refrigeration cycle, but can also operate in heating mode with a much higher efficiency than most types of boilers, especially electrical resistance boilers.

Due to their reversible operation, water-source heat pumps offer great flexibility in residential buildings. Individual units can be set to operate in different modes, and in combined heating and cooling applications the overall system can be extremely efficient:

  • Heat pumps in cooling mode extract heat from indoor spaces and release it into a common water circuit.
  • Then, heat pumps in heating mode can extract the heat now carried by the water, and release it indoors, as required.

The fact that heat pumps share the same water circuit means that the cooling tower and boiler only have to balance system loads, rather than meeting them fully:

  • If the cooling load is greater than the heating load, the cooling tower only has to reject the heat difference, not the total heat removed from all spaces.
  • The same logic applies if the heating load is higher than the cooling load: the boiler only has to make up for the difference, not the full heating load.
  • If the heating and cooling loads happen to balance each other out, both the cooling tower and boiler can remain off.

A four-pipe system lacks these capabilities: the chiller must assume the full cooling load while the boiler provides the full heating load – all the heat absorbed in the chilled water loop is rejected by the cooling tower, and can’t be used for space heating purposes because water circuits are independent.

HVAC systems based on water-source heat pumps are extremely efficient, although expensive due to the fact that every zone must be equipped with an individual heat pump, in addition to having a common water circuit, a cooling tower, and a boiler.

Mechanical Design Option #3: VRF System with Rooftop Condensers & Gas Boiler

VRF stands for variable refrigerant flow, and VRF systems get their name from the fact that refrigerant is used to transport heat instead of water:

  • One or more remotely located condensers provide a flow of refrigerant for multiple indoor fan-coils, and a variable speed drive is used to regulate flow according to load. The units can also provide their own heating.
  • For supplementary heating, a gas-fired boiler with perimeter radiation can be added to the system.
  • Two-pipe VRF systems require all fan-coils to operate in the same mode, but with three-pipe systems, it is possible to provide simultaneous heating and cooling for different areas of the building.

Other than operational flexibility, an advantage of this mechanical design option is their ease of installation: refrigerant lines are more compact than water piping and air ducts. These systems still have a relatively small market share in the USA, but are very common in Japan, where they were developed, and Europe. According to ASHRAE, VRF systems tend to have a comparable cost to that of chiller-based systems, potentially higher if the technology must be imported.

The modular nature of VRF systems is another strong point in favor of this technology. If there will be a building expansion, it is possible to expand the system by simply adding a new condenser and the corresponding indoor evaporators.

Mechanical Design Option #4: PTAC Units with Electric Resistance Heating

Packaged terminal air conditioning units (PTAC) are compact systems, very similar to old window-type air conditioners: the system is self-contained and does not require refrigerant lines, water piping, or air ducts, greatly reducing the installed cost. Some PTAC units are equipped with a resistance heater, allowing them to operate in both heating and cooling modes.

PTAC units offer the advantage of being self-contained and independent from each other. This gives them an advantage in projects that will be built in several stages, for example, apartment buildings, since it is possible to expand HVAC capacity as needed without having a common system on which all units depend.

The main limitation of this mechanical system is that they tend to be outclassed by other systems in terms of efficiency, especially when in heating mode. Resistance heating offers a coefficient of performance of 1.0, which means they must draw one watt of electricity per each watt of heating; on the other hand, heat pumps typically operate with a COP of 2.5 or more, or even above 4.0 if a high-efficiency heat pump is selected.

Concluding Remarks

There is a broad range of heating and cooling technologies available for residential buildings, and also a high degree of flexibility in how the overall system can be configured. No system can be considered superior to the rest under all circumstances – every project offers unique conditions that favor some technologies over others.

What kind of mechanical engineering design has worked the best for you? Let us know by commenting below.

Top Ssearch Queries Related to HVAC Companies near Chicago