HVAC Moline2018-12-03T19:51:38+00:00

HVAC Moline | Expert Power Efficient System Designs

Electrical Engineers
Contact Us!

Don’t be misled by the name New York Engineers is your best bet if you are looking for Full Service Air Conditioning, Heating & Cooling (HVAC) Engineering Firm in Chicago Illinois. We’re not only an HVAC Chicago but also a leading provider of Construction Engineering Engineering services throughout Moline. Call 312 767.6877

Contact Us!

In recent times huge crowds have been visiting our site looking for Mechanical Engineering in Chicago. That is due because of the reputation we have develop in this types of projects. However, many builders from Lemont to Posen, IL, are not aware that NY-Engineers.Com is also a top choice for anyone in search of HVAC Chicago!

The search for energy-efficient buildings involves energy-efficient HVAC system design. This can include systems for architectural enclosure, domestic water heating, lighting, HVAC, and vertical transportation. The loads for your HVAC systems can come primarily from 5 different sources including lighting (cooling), the construction envelope (cooling and heating), ventilation (cooling and heating), equipment for program use (cooling) and occupancy (cooling).
The ventilation load will be a function of either the instruments needed in order to introduce it right into a space and control contaminant concentration or the quantity of persons that may be in the space. In nearly all climates in the southwestern and eastern parts of the united states, to reduce outside air movement can save energy whenever the outer air is either humid and warm or very cold.
Manipulating the ventilation rate is going to be dependant upon occupancy which is known as a type of demand control ventilation. It is a common type of energy conservation tatic which is used for rooms with occasional or dense occupancy. Having cooling and heating loads reduced to a minimum can be accomplished by utilizing a higher performance building envelope, occupancy sensors, and performance lighting that exploits daylight response of lighting controls.

Chicago HVAC Engineering services vs HVAC Techs

If you have ever considered the distinction between a HVAC Engineers versus HVAC Engineers, then keep reading:

HVAC engineers are definitely the people that run installing of air cooling systems for both residential and commercial buildings. They spend plenty of their time in offices doing higher level organization and preparation of installations nonetheless they do also go to job sites every now and then.

In contrast, HVAC technicians have a tendency to do a lot of hands-on work  that deals with repair and maintenance. A HVAC tech may work with or for an engineer to do some of the installation work, especially on smaller jobs. Generally speaking HVAC techs do considerably more travel and could spend considerable time changing filters, identifying leaks, doing recharges or decommissioning old and outdated systems that utilize old refrigerants.

HVAC engineers might have the opportunity to make more decisions about systems that are used, and they also are the folks that would offer advice about probably the most sensible refrigerants and which systems would best suit a greater building. In the trade, there is some challenge between ‘the suits’ and ‘the ones which get their hands dirty’, but both jobs require a good understanding of how air cooling is proven to work. Nowadays huge crowds have been browsing our website searching for HVAC Companies Chicago Il. However, the focus of our company is to become the number one choice for anyone looking for a HVAC Firm near Chicago and or any of our other services including Value Engineering Engineering services. We ask that everyone looking for more info about our Heating Cooling Air Conditioning Furnace (HVAC) Engineering Firm in Chicago Illinois stops by at our Engineers Reports blog!

Top Blog Related to HVAC Companies in Chicago

An HVAC Engineering Professional Explains Types of Compressors Used in Chillers

Electrical Engineering Information

The compressor performs a fundamental role in the operation of a chiller, making it possible to remove heat from indoor spaces or from industrial processes via HVAC engineering. Once the refrigerant in a chiller absorbs the heat from a building or process it becomes a gas, but it is incapable of releasing the heat right away in this form. However, after the compressor raises the pressure and temperature of the gasified refrigerant, the heat can be expelled. Air-cooled chillers release heat directly outdoors, while water-cooled chillers release it into a stream of water that is then pumped to a cooling tower.

There are many types of compressors, each with advantages and disadvantages. This article will provide an overview of the three types most commonly used in large commercial chillers. HVAC engineers can determine the best option for your building based on load characteristics.

  • Reciprocating compressor
  • Centrifugal compressor
  • Rotary-screw compressor

In commercial space cooling systems, the compressor is typically the component with the highest electricity consumption. Therefore, it is important to have a well-sized unit, and of a type that is suitable for the application at hand.

Reciprocating Compressors

The reciprocating compressor has a shape similar to that of a car engine cylinder, and it is also known as piston compressor for this reason. Refrigerant that has evaporated after absorbing heat is fed into the cylinder through suction valves, and compressed by the piston before being sent to the condenser.

For a given cooling capacity, reciprocating compressors have a lower upfront cost than centrifugal and rotary-screw compressors in HVAC engineering. They also offer design flexibility, allowing multiple units to be installed together to serve variable cooling loads – individual units are activated or deactivated as needed.

The main limitations of reciprocating compressors are their lower energy efficiency and their demanding maintenance, compared with other types of compressors. Also, although these compressors can achieve good capacity control when multiple units are used, there are few options to modulate the capacity of an individual unit. The two most common options are:

  • ON/OFF Control: Operating the unit intermittently (reduced duty cycle) when its full capacity is not required.
  • Cylinder Unloading: The compressor cylinder can be equipped with additional suction valves or a clearance valve. These valves remain closed when the unit operates at 100% capacity, but may be opened in several combinations to achieve reduced capacity.

Centrifugal Compressors

If a reciprocating compressor can be compared to a car engine, this type is comparable to a water pump because it also uses an impeller, with the difference that it operates with refrigerant. These compressors are also available in hermetic and open models, where the open construction offers higher efficiency.

At rated load, centrifugal compressors are more efficient than both reciprocating and rotary-screw compressors. They also offer a compact construction and are available in a wide range of cooling capacities. Capacity control is normally achieved with inlet vanes that increase or decrease the flow of refrigerant into the impeller.

Despite their superior efficiency at full load, centrifugal compressors suffer from a drastic loss of efficiency at part-load. At very low cooling loads they are rendered unable to operate, due to a phenomenon called surging: refrigerant that is already compressed flows back into the impeller, disrupting its operation.

Centrifugal compressors have the least number of moving parts among the three main compressor types, which means there are less components to service.

However, in most cases the impeller must be factory-ordered if fails; suppliers rarely keep stock because it’s a highly specialized component. Balancing and vibration must also be checked frequently to avoid loss of performance and premature component failure.

Rotary-Screw Compressors

This type of compressor uses two helical screws that are designed to mesh with one another seamlessly while rotating at high speed. They are manufactured with high precision to create a clearance between them, which serves as the compression chamber. These compressors are available in hermetic and open versions like the two previous types described, and capacity control is achieved with a special valve that varies the internal volume ratio.

Although centrifugal compressors are more efficient at full load, rotary-screw compressors offer the best performance during part-load operation. Since the cooling load on a building varies throughout the year, rotary-screw compressors tend to achieve the lowest operating cost overall, even if centrifugal compressors are more efficient at full load.

The main limiting factor of rotary-screw compressors is their high price. If the application does not provide opportunities to take advantage of their capacity control and their superior part-load efficiency, another type of compressor can be considered.

HVAC Engineering: Choosing the right Compressors

High-rise commercial buildings, like those found in many major cities, can generally achieve the best results with a space cooling chiller that uses a rotary-screw compressor. Despite being the most expensive option, it offers the best performance under the variable cooling load that characterizes buildings, while being the simplest system to service – consider that maintenance activities can be quite disruptive in a busy commercial property.

Working with qualified HVAC engineering experts ensures that your property gets a space cooling system that delivers high performance at an optimal energy cost. Chiller selection is a key element, but it is also important to specify adequate complementary systems: air handling units, hydronic piping, cooling towers, HVAC controls, etc.

Ssearch Queries Related to HVAC Chicago