HVAC Ravenswood Chicago2018-12-06T02:10:54+00:00

HVAC Ravenswood Chicago | Expert Energy Efficient System Designs

Electrical Engineering Basics
Contact Us

Do not be misled by our NY Engineers is your best option if you are looking for Full Service Air Conditioning, Heating & Cooling (HVAC) Engineering Firm in Chicago Illinois. We’re not only an HVAC Firm in or near Chicago but also a leading provider of Sprinkler System Engineering services throughout Ravenswood Chicago. Call us at 312 767.6877

Contact Us

Recently A lot of people have been visiting our site in search of Fire Protection Engineering in or near Chicago. This is due because of the reputation we have develop in this types of projects. Nevertheless, a lot of building owners from Darien to Westchester, IL, are not aware that NY Engineers is also a top contender for anyone searching for HVAC Chicago.

The quest for power efficient buildings involves energy efficient HVAC system design. This will likely include systems for HVAC, lighting, architectural enclosure, domestic water heating, and vertical transportation. The loads for your HVAC systems should come primarily from 5 different places including lighting (cooling), the building envelope (cooling and heating), ventilation (cooling and heating), equipment for program use (cooling) and occupancy (cooling).
The ventilation load will certainly be a function of either the machines necessary to be able to introduce it in to a space and control contaminant concentration or the number of individuals that can use the area. In virtually all climates inside the southwestern and eastern regions of the US, to lessen outside ventilation can save energy whenever the exterior air is either warm and humid or very cold.
Managing the ventilation rate will likely be dependant upon occupancy which is known as a kind of demand control ventilation. This can be a common type of energy conservation strategy that is used for homes with irregular or dense occupancy. Having cooling and heating loads reduced as low as possible can be accomplished by utilizing an increased performance building envelope, occupancy sensors, and performance lighting that exploits daylight response of lighting controls.

Chicago HVAC Engineering services versus HVAC Technicians

If you have ever discussed the distinction between a HVAC Engineers versus HVAC Engineers, then read on:

HVAC engineers are definitely the people that run the installation of air cooling systems both for commercial and residential buildings. They spend a lot of their work in offices doing advanced level management and arranging of installations nevertheless they do also visit job sites every once in awhile.

In contrast, HVAC technicians usually do a lot of hands-on work with repair and maintenance. A HVAC technician may assist an engineer to do some of the installation task, particularly for smaller jobs. Generally speaking HVAC techs do much more travel and might spend time and effort changing filters, identifying leaks, doing recharges or getting rid of old and outdated systems which use old refrigerants.

HVAC engineers could have the chance to make more decisions about systems that are used, and they also are definitely the people that would offer advice about by far the most sensible refrigerants and which systems would best suit a greater building. In the trade, there exists some rivalry between ‘the suits’ and ‘the ones which get their hands dirty’, but the two jobs do require an effective knowledge of how air-con works. Nowadays huge crowds have been crawling our sites searching for things like HVAC Chicago Illinois. However, the focus of our company is to become the top option for anyone seeking a HVAC Firm near Chicago and or any of our other services including Sprinkler Engineering services. Furthermore everyone looking for additional info about our Heating Cooling Air Conditioning Furnace (HVAC) Engineering Firm in Chicago Illinois checks out at our blog…

Latest Article Related to HVAC Companies near Chicago

An HVAC Engineering Professional Explains Types of Compressors Used in Chillers

Electrical Engineering Information

The compressor performs a fundamental role in the operation of a chiller, making it possible to remove heat from indoor spaces or from industrial processes via HVAC engineering. Once the refrigerant in a chiller absorbs the heat from a building or process it becomes a gas, but it is incapable of releasing the heat right away in this form. However, after the compressor raises the pressure and temperature of the gasified refrigerant, the heat can be expelled. Air-cooled chillers release heat directly outdoors, while water-cooled chillers release it into a stream of water that is then pumped to a cooling tower.

There are many types of compressors, each with advantages and disadvantages. This article will provide an overview of the three types most commonly used in large commercial chillers. HVAC engineers can determine the best option for your building based on load characteristics.

  • Reciprocating compressor
  • Centrifugal compressor
  • Rotary-screw compressor

In commercial space cooling systems, the compressor is typically the component with the highest electricity consumption. Therefore, it is important to have a well-sized unit, and of a type that is suitable for the application at hand.

Reciprocating Compressors

The reciprocating compressor has a shape similar to that of a car engine cylinder, and it is also known as piston compressor for this reason. Refrigerant that has evaporated after absorbing heat is fed into the cylinder through suction valves, and compressed by the piston before being sent to the condenser.

For a given cooling capacity, reciprocating compressors have a lower upfront cost than centrifugal and rotary-screw compressors in HVAC engineering. They also offer design flexibility, allowing multiple units to be installed together to serve variable cooling loads – individual units are activated or deactivated as needed.

The main limitations of reciprocating compressors are their lower energy efficiency and their demanding maintenance, compared with other types of compressors. Also, although these compressors can achieve good capacity control when multiple units are used, there are few options to modulate the capacity of an individual unit. The two most common options are:

  • ON/OFF Control: Operating the unit intermittently (reduced duty cycle) when its full capacity is not required.
  • Cylinder Unloading: The compressor cylinder can be equipped with additional suction valves or a clearance valve. These valves remain closed when the unit operates at 100% capacity, but may be opened in several combinations to achieve reduced capacity.

Centrifugal Compressors

If a reciprocating compressor can be compared to a car engine, this type is comparable to a water pump because it also uses an impeller, with the difference that it operates with refrigerant. These compressors are also available in hermetic and open models, where the open construction offers higher efficiency.

At rated load, centrifugal compressors are more efficient than both reciprocating and rotary-screw compressors. They also offer a compact construction and are available in a wide range of cooling capacities. Capacity control is normally achieved with inlet vanes that increase or decrease the flow of refrigerant into the impeller.

Despite their superior efficiency at full load, centrifugal compressors suffer from a drastic loss of efficiency at part-load. At very low cooling loads they are rendered unable to operate, due to a phenomenon called surging: refrigerant that is already compressed flows back into the impeller, disrupting its operation.

Centrifugal compressors have the least number of moving parts among the three main compressor types, which means there are less components to service.

However, in most cases the impeller must be factory-ordered if fails; suppliers rarely keep stock because it’s a highly specialized component. Balancing and vibration must also be checked frequently to avoid loss of performance and premature component failure.

Rotary-Screw Compressors

This type of compressor uses two helical screws that are designed to mesh with one another seamlessly while rotating at high speed. They are manufactured with high precision to create a clearance between them, which serves as the compression chamber. These compressors are available in hermetic and open versions like the two previous types described, and capacity control is achieved with a special valve that varies the internal volume ratio.

Although centrifugal compressors are more efficient at full load, rotary-screw compressors offer the best performance during part-load operation. Since the cooling load on a building varies throughout the year, rotary-screw compressors tend to achieve the lowest operating cost overall, even if centrifugal compressors are more efficient at full load.

The main limiting factor of rotary-screw compressors is their high price. If the application does not provide opportunities to take advantage of their capacity control and their superior part-load efficiency, another type of compressor can be considered.

HVAC Engineering: Choosing the right Compressors

High-rise commercial buildings, like those found in many major cities, can generally achieve the best results with a space cooling chiller that uses a rotary-screw compressor. Despite being the most expensive option, it offers the best performance under the variable cooling load that characterizes buildings, while being the simplest system to service – consider that maintenance activities can be quite disruptive in a busy commercial property.

Working with qualified HVAC engineering experts ensures that your property gets a space cooling system that delivers high performance at an optimal energy cost. Chiller selection is a key element, but it is also important to specify adequate complementary systems: air handling units, hydronic piping, cooling towers, HVAC controls, etc.

Top Ssearch Queries Related to HVAC Chicago