HVAC Riverwoods2018-11-19T17:02:35+00:00

HVAC Riverwoods | Expert Energy Efficient System Designs

Architectural Engineering Vs Architecture
Contact Us!

Don’t be fooled by our NY Engineers is your best option if you need a Full Service Heating & Air Conditioning (HVAC) Engineering Firm in Chicago Illinois. We’re not only an HVAC Chicago but also a leading provider of Protection Engineering services in Riverwoods. Call (+1) (312) 767-6877

Contact Us!

Recently Hundreds of people have been visiting the NY-Engineers.Com site searching for Construction Engineering in or near Chicago. This is due because of the reputation we have built in this types of projects. However, many building owners from Inverness to Springfield, Illinois, are not aware that NY Engineers is also a top choice for anyone looking for HVAC Company in or near Chicago!

The quest for power efficient buildings involves energy efficient HVAC system design. This may include systems for HVAC, lighting, architectural enclosure, domestic water heating, and vertical transportation. The loads for your HVAC systems may come primarily from 5 different sources including lighting (cooling), the construction envelope (cooling and heating), ventilation (cooling and heating), equipment for program use (cooling) and occupancy (cooling).
The ventilation load might be a purpose of either the devices necessary to be able to introduce it in a space and control contaminant concentration or the amount of persons that may use the area. In virtually all climates within the southwestern and eastern parts of the US, to reduce outside air movement helps save energy whenever the

outside air is either humid and warm or very cold.
Controlling the ventilation rate will be based on occupancy which is referred to as a form of demand control ventilation. This is a everyday sort of energy conservation approach that is utilized for buildings with intermittent or heavy occupancy. Having cooling and heating loads reduced as low as possible can be achieved by using a higher performance building envelope, occupancy sensors, and high performance lighting that uses daylight response of lighting controls.

Chicago HVAC Engineering services versus HVAC Techs

When you’ve ever discussed the distinction between a HVAC Technician vs HVAC Technicians, then continue reading:

Chicago HVAC engineers are the people who supervise installing of air conditioner systems both for commercial and residential buildings. They spend plenty of their time in offices doing more impressive range supervision and planning of installations nevertheless they do also stop by job sites every once in awhile.

In contrast, HVAC technicians in Chicago usually do a lot of hands-on work with repair and maintenance. A HVAC technician may assist an engineer to complete some of the installation task, specifically on smaller jobs. On the whole HVAC technicians do considerably more travel and may even spend a lot of time identifying leaks, changing filters, doing recharges or decommissioning old and outdated systems which use old refrigerants.

HVAC engineers might have the chance to make more decisions about systems that are employed, and they will be the people that would offer advice about one of the most sensible refrigerants and which systems would be perfect for a larger building. In the trade, there may be some conflict between ‘the suits’ and ‘the ones that get their hands dirty’, but the two jobs require a great knowledge of how air cooling works. Nowadays huge crowds have been checking out the New York Engineers site looking for things like HVAC Chicago Show. However, the focus of our company is to be the number one choice for anyone looking for a HVAC Firm in Chicago and or any of our other services including Sprinkler Design Engineering services. We ask that anybody searching for more details about our Heating & Air Conditioning (HVAC) Engineering Firm in Chicago Illinois visits at our blog.

New Blog Article Related to HVAC Contractor near Chicago

Electrical Safety and Power Quality: A Short Guide for Electrical Engineering

Electricity is one of the cornerstones of modern society, but it can be very dangerous if handled incorrectly. Therefore, governments have introduced stringent codes to regulate its use and ensure safety for occupants. A building’s power supply must be safe to use, and it must also have the voltage and frequency required by the electrical appliances in the building. The electrical engineering systems that provide electrical safety and power quality are typically hidden from sight, but they play a fundamental role in buildings.

Electrical issues are more common in pre-war apartment buildings and other old constructions. Always make sure you get the installation checked before moving into an existing property, but especially if it very aged.

Electrical Protection Devices

The main function of electrical protections is to disconnect the power supply when dangerous operating conditions are present. The main types of electrical faults found in electrical engineering systems are the following:

  • Overload or overcurrent
  • Short circuit
  • Ground fault
  • Line-to-line fault
  • Transient or voltage surge

Plug-in circuit breakers are perhaps the best-known electrical protection devices, commonly used in residential and light commercial applications (below 100 Amperes). Molded-case circuit breakers are generally larger and reach higher current ratings, while motor circuit protectors and thermal overload relays are designed for the protection needs of electric motors. Other than the plug-in configuration, there are protection devices designed for a DIN rail mount or for bolted connections.

An overload occurs when an electrical circuit is drawing current above its rated value for an excessively long period. It is important to note that short-duration overcurrent is common in some types of equipment. For example, three-phase electric motors may draw up to eight times their rated current during startup, but only for a short time – typically fractions of a second. Some types of lighting also draw an inrush current, especially if they have ballasts.

Circuit breakers typically use a thermal interruption mechanism to protect circuits from overload while allowing short-duration current peaks. The thermal protection mechanism uses a metallic contact that expands when heated by current, and it is calibrated to allow the circuit breaker’s rated current but not higher values. However, since inrush currents occur too quickly, their heating effect is not enough to expand and disconnect the thermal protection mechanism. On the other hand, an overload eventually trips the breaker; as current magnitude increases, the thermal protection contact expands faster and disconnects the circuit in less time.

A short circuit occurs when a live conductor touches a neutral conductor, causing a very high current. The magnitude of a short circuit fault is very high, typically thousands of amperes, so it must be disconnected as quickly as possible. In this case the response of thermal protection is too slow, so the protection mechanisms that clear short circuit faults are based on electromagnetic induction – the intense current induces a strong magnetic field that disconnects the circuit breaker.

A ground fault, also known as a line-to-ground fault, occurs when a live conductor touches a conductive element that is not part of the electric circuit. This also creates a very high current due to the low contact resistance, activating the magnetic protection mechanism of the respective circuit breaker. A line-to-line fault occurs when two live conductors at different voltage touch each other, also causing a high-magnitude current. In both cases, the same magnetic protection mechanism that clears short circuit faults responds and trips the circuit breaker.

All the faults described above are characterized by excessive current. When a high voltage peak occurs, the fault is called a transient or a voltage surge. Voltage surges normally occur when large equipment is switched, and can also be caused by lightning. Since circuit breakers are not designed to protect installations from voltage surges, you must use a surge protection devices (SPD) or transient voltage surge suppressor (TVSS). One of the most common types of TVSS use a variable resistance (varistor) connected between the live conductors and the ground – its resistance is high under normal operating conditions, but drops to a very low value in response to voltage peaks, discharging the fault to the ground before it reaches sensitive equipment.

Improving Power Quality in Electrical Engineering Systems

Electric power systems may also suffer from issues that are not faults strictly speaking, but which are also detrimental for performance. Two of the main issues are low power factor and harmonics.

Power factor is a very abstract concept, but the following is a simple way to visualize it. Some types of electrical equipment draw current in such a way where not all the power drawn from the voltage supply is really consumed. In these cases, the term “real power” is used to describe the power that is actually used, and the term “reactive power” is used to describe the portion that oscillates back and forth between the equipment and the power supply without being used. Some of the most common loads associated with reactive power are electric motors, transformers and ballasts. The power factor is the ratio of the real power used and the apparent power – the direct multiplication product of voltage and current.

  • Assume a single-phase motor consumes 900 W of electric power while drawing 5 amperes at 240 volts.
  • The apparent power is 1,200 volt-amperes (240V x 5A).
  • The power factor is 0.75 (900W / 1200 VA). It can also be reported as 75%.
  • The maximum possible value is 1.00 or 100%, where all the power drawn from the voltage source is consumed. Purely resistive loads such as incandescent lamps and resistance heaters behave this way.

Low power factor increases the current drawn by a building, and this creates an extra burden for the grid. Therefore, utility companies typically penalize users that allow their power factor to drop below a specified value. Low power factor is corrected by installing capacitors, which are similar to batteries but designed for a much faster cycle – the oscillating current that characterizes reactive power is supplied locally by the capacitor, and not drawn from the power grid, sparing the user from extra charges.

Power factor correction is characterized by its quick payback period, typically less than one year.

Harmonics are voltage and current signals whose frequency is a multiple of the service frequency – 60 Hz in the USA. Harmonics are produced by nonlinear loads such as magnetic cores and digital equipment, and they tend to overheat circuits, especially the neutral conductor. Excessive harmonics can also cause some types of electronic equipment to malfunction. Harmonic filters are devices that are tuned for a specific harmonic frequency, and when installed in a power system they prevent the propagation of harmonics beyond the equipment that generates them.

Conclusion

The best recommendation to keep all these electrical issues under control is to seek professional assistance from an electrical engineering profession. In new constructions, protection and power quality can be addressed from the design stage. For existing buildings, power monitoring equipment can be used to detect harmonics or low power factor, and the measurement results are then used to specify harmonic filters and capacitors. If circuit breakers are tripping frequently, get an inspection to determine the cause: there could be an electrical fault, but the breaker itself could also be damaged.

Top Searches Related to HVAC Chicago